← Resources

Standards library · FAQ

Stainless vs Spring Steel Lock Washers

Compare 304 stainless and coated spring steel split lock washers by corrosion environment, drawing callout, and RFQ requirements.

Stainless vs spring steel lock washers (short answer)

304 stainless split lock washers and coated carbon spring steel lock washers are not automatic substitutes. Both may use DIN 127-style dimensions, but the material, surface condition, corrosion behavior, and mechanical requirements must follow the drawing or approved RFQ.

Pisenfasten's published washer catalog focuses on metric 304 stainless. Browse spring lock washers, or send the drawing when the specified material is carbon spring steel, A4 / 316, or another grade.

Buyer comparison

Purchasing question304 stainlessCarbon spring steel
Corrosion behaviorBetter general corrosion resistance than uncoated carbon steel; not a universal solution for chlorides or chemicalsDepends heavily on the coating and exposure; coating damage can change corrosion performance
Typical surface stateStainless finish or passivated only when specified and confirmedPlain, black, zinc-plated, or another specified coating
Matching hardwareCommon with 304 / A2 stainless screws and nutsCommon where the drawing calls spring steel and a defined finish
What controls the orderMaterial grade, dimensions, standard, and required documentsMaterial, hardness or mechanical requirement, coating, dimensions, and required documents

DIN 127-style sizing identifies a washer form and dimensional family. It does not by itself define stainless versus spring steel, corrosion suitability, or approval for a safety-critical joint.

When 304 stainless is a reasonable starting point

304 stainless is commonly considered for indoor equipment, general industrial assemblies, and mild-corrosion environments where the rest of the joint also uses stainless hardware. It can reduce the coating-dependency of carbon steel, but it still requires an environment review.

Do not treat 304 as “chemical-proof.” Chlorides, coastal exposure, high temperature, acids, caustics, cleaning chemicals, and repeated wet/dry cycles can change the material decision. For process-service inquiries, use the chemical-processing fastener specification checklist.

When spring steel must remain spring steel

Keep carbon spring steel when the drawing or approved bill of material explicitly calls for it. The RFQ should state the finish or coating, any hardness or performance requirement, and the relevant dimensional standard. Do not replace it with 304 stainless only because both parts are described as split lock washers.

Joint-design boundary

A split lock washer is not a substitute for verified tightening torque, a prevailing-torque fastener, thread-locking compound, a tab washer, safety wire, or another engineered locking method. For vibration-sensitive or safety-critical joints, the assembly method must be approved by the responsible engineer.

For a basic washer-stack comparison, read flat vs spring washers.

RFQ checklist

Include these items so sales can review the requirement without guessing:

  1. Washer type: split / spring lock washer
  2. Nominal bolt or thread size
  3. ID, OD, thickness, or the governing drawing
  4. Material: 304 stainless, carbon spring steel, A4 / 316, or another specified grade
  5. Finish or coating, if applicable
  6. Service environment, including chemicals, temperature, chlorides, and wet/dry cycle
  7. Quantity, packaging, and ship-to country
  8. Required documents, inspection records, or traceability level

Copy/paste:

Split lock washer · [size / drawing] · [material] · [finish] · [standard] · [environment] · qty · ship-to · documents

Published 304 sizes and current commercial terms are shown on spring lock washers. For carton pricing or mixed replenishment, review Wholesale. For a non-catalog material, send an RFQ.

FAQ

Q: Is a stainless lock washer the same as a spring steel lock washer?
A: No. The shape may be similar, but material, coating, corrosion behavior, and mechanical requirements differ.

Q: Does DIN 127 mean the washer is spring steel?
A: Not by itself. Confirm the drawing's material and finish callout.

Q: Is 304 stainless suitable for chemical processing?
A: It depends on the chemical, concentration, temperature, chlorides, exposure cycle, and joint duty. Submit those inputs for review rather than relying on the word “stainless.”

Q: Can a split washer guarantee that a joint will not loosen?
A: No. Tightening method and joint design remain essential, especially for vibration-sensitive or safety-critical service.